Engine Options: • 17hp Kawasaki, air-cooled, twin cylinder, vertical shaft • 19hp Kawasaki, air-cooled, twin cylinder, vertical shaft • 20hp Briggs & Stratton ELS, air-cooled, twin cylinder, vertical shaft • 26hp Briggs & Stratton ELS, air-cooled, twin cylinder, vertical shaft Fuel Capacity/Design: • 6.5 gallon (36”) fuel tank with molded-in cupholder & storage tray • 7 gallon (48” & 52”) fuel tank with molded-in cupholder & storage tray Travel Control: Twin padded steering controls with gas dampers for smooth, precise maneuverability. Levers are adjustable. Ground Speed: 8mph forward, 5mph reverse Main Frame Construction: Steel tube frame, full-length, fully-welded Drive Tires: 18 x 7 - 8 (36”); 20 x 10 -8, 4 ply (48” & 52”) Caster Tires: 11 x 4.5 - 5, 4 ply Caster Pivot Bearings: Sealed ball bearings Drive System: Dual Hydro-Gear ZT-2800 integrated transaxles with charge pumps and spin- on oil filters; steel plate oil filter guards protect filters from damage Mower Maintenance: “Maintenance Free” mower design has no grease points, saving you maintenance time Electrical System: 12 Volt battery. Bendix starter. Engine Guard: Super-tough rear engine guard protects the engine compartment from potential impact damage when backing up Specifications Belts: Kevlar cord. Self-adjusting, spring-loaded, self-tightening. Drive/Load Pulleys: Steel pulleys. Steel dust and debris covers over idler pulley bearings to keep foreign material out and extend bearing life. Instrument Panel : Key switch, throttle, manual choke, BBC switch, digital “SmartSense” hourmeter within easy view Seat: Adjustable, fully cushioned seat with padded arm rests; retractable seat belt Foot Plate: Extra-large foot plate for improved comfort; easy to get on and off of mower. Pierced, extruded steel tread ensures solid footing. Rubber iso-mounted for additional operator comfort. PTO - Electric Clutch: Ogura, 87 ft/lb of torque / adjustable air-gap for long component life Cutter Decks: 36”, 48” & 52” decks. Floating, adjustable, anti-scalping design Cutter Deck Construction: Welded steel with 7-gauge deck skirt, 10-gauge top with 11-gauge reinforcement plate/baffles Cutter Deck Drive: Belt driven -- Straight belt for long life, not a twisted “mule” drive Anti-Scalp: One roller on left-front edge, two rollers on center-front edge, skid plate at rear-center of deck Cutter Deck Spindles: Heavy-duty, no-maintenance spindles with cast aluminum housing & sealed ball bearings; reliable, worry-free performance day in and day out Cutter Deck Height Adjustment: Foot pedal/peg lift with self-locking mechanism at transport position. Large knurled foot pedal/peg for “no-slip” deck lifting. Cutting Range: 1” to 4-1/2” in 1/4” increments. Easily adjustable while seated. Number of Cutter Blades: 3 Marbain blades Deck Leveling: 4-corner cutter deck adjustment mechanisms allow for easy deck leveling and pitch adjustment to ensure a smooth, even cut Total Length: 73" Total Width (with discharge chute in mowing position): • 36" models: 48.5" • 48" models: 60.5" • 52" models: 64.5" Total Width (with discharge chute in transport position): • 36" models: 37" • 48" models: 49" • 52" models: 53" Height: 60” Weight: • 36" models: 690 lbs. • 48" models: 775 lbs. • 52" models: 785 lbs. Warranty: • 3 Yr. Residential Mower Warranty*—Parts & labor • 1 Yr. Commercial Mower Warranty*—Parts & labor • 2 Yr. Engine Warranty—Minimum two-year warranty covered directly through the individual engine manufacturer.